Worse: Cutting the pipe and measuring revealed that more intermediate lines are needed for less than 1 degree error. I have no idea what makes just this (tricky) chamfer good.ĪDD after a comment The questioned asked how I guarantee that the chamfering result is 15 degrees tilted from the horizontal everywhere, not only at the rotated lines which are blended to a surface? I must admit I cannot prove it, the result looks right only visually. Here's the used blending under construction:Īnd this is the chamfered pipe end completed:īTW.
Here's the cutting result - only half a turn done, the orange (=selected) surface is the original tilted pipe end for a comparison: Or instead of cutting extrude the blending result and subtract. The edge of the pipe end is the blending path. but I can show one idea:Ĭut with a surface which is a blend between 2 lines which both are tilted 15 degrees from the horizontal. Sorry, no Inventor available here, I use freeware. Is there another way of generating this chamfer or removal? I just forgot, I also tried a helix (coil) cut, but the path of the helix is not the same as the angled cut through the pipe. I even added a rail of the inside edge which improved things but still had problems. The resulting shape did not follow the radius of the pipe when viewed on end. I made 4 sketches, one at each quadrant, and selected closed loop. Sweep has some serious issues relative to the desired output. The blue line is the 15 degree from horizontal line from the sketch at the low end. It was as if the triangle did not remain in its original horizontal position but got twist as it followed the path. However the resulting cut from that was not good at all. Then I thought about using the sweep tool and selecting the inside edge and tip of the triangle. I initially was going to revolve it, but that does not work as the path it need to follow is not circular. I also tried creating triangle to cut out the required shape. Since the 15 degree angle is relative to the horizontal plane, the depth along the side of the pipe also varies. The problem is the width of the top face varies ever so slightly due to the angled cut through the piped. The tool requires either fixed distance on both faces or a fixed distance on one face and an angle from that face. I tried applying a chamfer using the tool which was probably the closest result I got but it had a problem. The problem is the last and final step of applying a 15 degree chamfer to top face of the pipe.
I then applied a 6 mm fillet to the inside edge of the added plate and pipe, followed by an 10 mm fillet to the outside edge. The section a bounding box the extrude and remove material from the lower pipe that does not belong. The first to be essentially a plate to be extruded into the remaining pipe. I then proceeded to create a work plane on the face of the lower cut and proceed to added two shapes. I followed this up by extruding triangles at the top and bottom to generate the angled cuts. I then revolved the large rectangle on the right side to generate a section straight pipe. I started out by drawing up the section on the left in a 2D sketch and then added some cutting shapes. I know how I attempted to model this piece but I am not sure on the proper way to model this. Therefore there is no original designer/engineer I could got to for clarification. The venue offers veg and non vegetarian cuisine on its premises.Ĭontact them to find availability and best deals for your wedding date.The part above is from 1944 V2 plans which I am using as real world practice examples to teach myself 3D modeling using Inventor LT 2021. The venue caters to weddings using its own inhouse kitchen offering various delicacies for wedding guests. In house DJ not available, Outside DJ permittedĪllow small size gathering for pre wedding functions In house alcohol not available, Outside alcohol permitted If intimate and close events is what you are looking for your haldi or other small functions, Hotel West End View is the perfect place.įacilities provided by Hotel West End View: The venue primarily functions as a small event space perfect for pre-wedding functions like engagement, roka, mehendi as it has a maximum capacity of 70pax. The venue has 21 rooms available making it perfect for out of town guests or the wedding family to move in for wedding celebrations. The venue has Indoor spaces available which can accomodate up to 70 guests and hence a popular option for weddings in Zirakpur. Hotel West End View is a Banquet hall located in Dhakoli, Zirakpur.
0 kommentar(er)
